Natural Stone Impregnating Protector (HGP32) 1 Litre

Homecare Essentials > HG Hagesan Cleaning Products
> HG Hagesan Bulk Case Sizes - SAVE 10% > Bulk Products 81-88 (M-P) > Natural Stone Impregnating Protector (HGP32) 1 Litre

Case of 6 x HG Natural Stone Impregnating Protector (HGP32) 1 Litre Ref: HGP32case

Case of 6 x HG Natural Stone Impregnating Protector (Product 32) 1 Litre

HG Natural Stone Impregnating Protector is used to impregnate porous marble, travertine, terrazzo, granito, slate, sandstone, limestone and other natural stone floors and walls to protect against stains and stubborn marks. Extremely suitable for concrete tiles with pieces of natural stone incorporated such as marble composites.

For terracotta tiles, brick, quarry tiles, victorian tiles, flagstones, un-glazed (porcelain or ceramic) tiles we recommend HG Impregnating Protector Sealer (HGP13) which has larger molecules and it is therefore slightly thicker making it more suitable for more porous materials.

To check the porosity of a surface to see if treatment is required use a tablespoon of water. If after 5-10 minutes none of the water has been absorbed into the surface the surface is sealed.

HG Natural Stone Impregnating Protector penetrates deep into the surface and completely seals off small pores. Larger pores are made smaller meaning liquid molecules can no longer be absorbed preventing the formation of stains and dirt. However, any dampness in the floor can still evaporate.

HG Natural Stone Impregnating Protector still allows the stone to breathe. Does not change (or hardly changes) the original characteristics of the material.

HG Natural Stone Impregnating Protector leaves a matt finish enhances natural colours, does not contain silicone. It is suitable for inside and outside use.

Coverage: Highly porous natural stone: 10-20 m² per litre. Slightly porous and high gloss natural stone 20-50 m² per litre.

6 x 1 Litre 5 Litre size also available CLICK HERE

Also available individually Click Here

Click here to see the complete HG Marble Care Range.

Click here to download Safety Data Sheet (pdf).

Price: £133.22 Including VAT at 20%

Viewing this content on a mobile device? Tap here to call us and order.

Quantity:

Enter e-mail address to tell a friend about this product

HG Hagesan Natural Stone Impregnating Protector (HGP32) - Usage Instructions

Directions for use:

Make sure that an existing floor has not yet been treated with HG Natural Stone Impregnating Protector (HGP32) or another similar basic treatment. Carry out a porosity test if unsure.

It is advisable to ventilate well during the use of this product in order to speed up the drying process.

1. The surface to be treated with HG Natural Stone Impregnating Protector (HGP32) must be perfectly clean and free from grease and dirt.

For the removal of cement and mortar stains, first clean with HG Marble and Cement and Lime Film Remover. Grime and old wax and polish layers have to be removed beforehand with HG Marble Stripper. Leave the floor to dry for 3 days after using HG Marble Stripper.

For really dirty floors use HG Super Remover.

After rinsing off allow at least 3 days (24 hours with under floor heating) for the surface to dry thoroughly to ensure that Impregnating Protector can be fully absorbed.

Highly porous tiles such as Sandstone, will need even more time to completely get rid of the water. For this type of tile we recommend at least 1 week (24 hours with under floor heating).

2. The glue/cement and grouting of new floors must be completely hardened and dry. The drying time is usually 4-6 weeks.

3. HG Natural Stone Impregnating Protector is used neat (undiluted). Apply evenly, in one direction with our Superfine Roller.

TIP: On (high) gloss floors, HG Natural Stone Impregnating Protector must be applied and polished out using a lint free cloth.

4. If the HG Natural Stone Impregnating Protector has not penetrated and remains on the tiles 10 minutes (maximum) after application this will need to be removed straight away with a clean lint-free cloth.

If the HG Natural Stone Impregnating Protector is fully absorbed and no surplus is required to be wiped off, a second/third treatment may be needed until the Natural Stone Impregnating Protector is no longer absorbed.

* VERY IMPORTANT: Over application of Natural Stone Impregnating Protector is very common - a second coat is rarely needed and excess HG Natural Stone Impregnating Protector needs to be removed quickly. Excess Natural Stone Impregnating Protectorwill sit on the surface and will give a streaky appearance if left. If the Impregnator is allowed to dry on the surface it CANNOT be removed - it will have to be left to wear off.

After treatment with HG Natural Stone Impregnating Protector the surface should retain a matt appearance. Allow at least one hour before applying a second or more coats depending on porosity.

5. After approx. 3 hours the surface can be walked upon and is completely protected 12 hours after the final treatment.

Once absorbed the treatment of HG Natural Stone Impregnating Protector is permanent.

For additional surface protection see HG Natural Stone Protective Gloss Coating (HGP33) and HG Natural Stone Protective Coating Matt Finish (HGP34).

Coverage: Highly porous natural stone: 10-20 m² per litre. Slightly porous and high gloss natural stone 20-50 m² per litre.

Maintenance: Use HG Natural Stone Shine Restoring Cleaner (HGP37) or HG Natural Stone Polished Tile Cleaner (HGP38).

Attention: Keep in a frost free area. When using HG Natural Stone Impregnating Protector we recommend using protective gloves.

TIP: If a floor treated with this product is not also treated with a specific surface protector such as HG Natural Stone Protective Gloss Coating (HGP33) or HG Natural Stone Protective Coating Matt Finish (HGP34) we recommend repeating treatment with this product every 1 to 2 years in walkways and intensively used areas. Protection of the top layer by this product will gradually be reduced as a result of general wear.

6 Inch Superfine Roller Set Ref: ROLLERSET

Superfine Roller Set

The complete set for applying a number of HG Hagesan Products. Save 50p on individual prices too!

Set contains 6 Inch Superfine Applicator Roller with frame (choice of frame size) and a 6 Inch Roller Tray.

Recommended for use with the following HG Hagesan Products:

1. HG Tile Impregnating Protector.
2. HG Natural Stone Impregnating Protector.

Click here for more information

Viewing this content on a mobile device? Tap here to call us and order.

Quantity:

Choice of Frame Length

Choose Length

Enter e-mail address to tell a friend about this product

Superfine Applicator Roller - 6 Inch Ref: FDDMRF16

Superfine Applicator Roller

Superfine dense foam mini paint rollers sleeves / refills, manufactured using state of the art machinery. Exceptional foam quality for serious application jobs. Achieves a smooth bubble-free finish. For use with solvent-borne gloss, primers, lacquers, acrylic and synthetic resin varnishes, water-borne acrylic paints and liquid adhesives with low-solvent contents.

Suitable for the smallest most difficult to reach areas with full corner coverage.

Push on/Pull off design for use with standard 6 Inch Rollers Frames. Outer diameter 35mm.

Superfine foam mini paint roller sleeves are rounded on the frame side, except for the 5cm size which is straight on both ends.

Recommended for use with the following HG Hagesan Products:

1. HG Tile Impregnating Protector.
2. HG Natural Stone Impregnating Protector.

Price: £2.68 Including VAT at 20%

Viewing this content on a mobile device? Tap here to call us and order.

Quantity:

Enter e-mail address to tell a friend about this product

6 Inch Roller Frames Ref: FDDMR

6 Inch Roller Frames

Galvanised steel mini paint roller frame for use with our 6 Inch Superfine Applicator Rollers. Robust plastic handle with hanging hole. Accepts standard push fit extension poles.

The long-handled frame allows you to apply the product standing up.

Available in two different frame lengths - standard (27cm) and long (55cm).

Viewing this content on a mobile device? Tap here to call us and order.

Quantity:

Choice

Choose Length

Enter e-mail address to tell a friend about this product

6 Inch Roller Tray Ref: FDDPT6

6 Inch Roller Tray

This plastic 6 Inch Roller Tray is ideal for using as a container for the product when applying several HG Hagesgan products with our 6 Inch Rollers Frames and 6 Inch Superfine Applicator Rollers.

Made in the UK.

Price: £2.12 Including VAT at 20%

Viewing this content on a mobile device? Tap here to call us and order.

Quantity:

Enter e-mail address to tell a friend about this product

**sRecentPrefix**

<br/><br/>
<div class="recenththeader">
<input class="recenthtbuttonright" id="scrollbackrecent" type="button" value="    Next >>" onclick="ScrollBackRecent();">
<input class="recenthtbuttonleft" id="scrollforwardrecent" type="button" value="<< Previous" onclick="ScrollForwardRecent();">
<div style="text-align:center">Recently Viewed</div>
</div>
<br clear="all"/>
<table id="recenthtitem">

**sRecentImageRowPrefix**

**sRecentImageItem**

**sRecentImageRowSuffix**

</tr>

**sRecentDescRowPrefix**

<tr>

**sRecentDescItem**

**sRecentDescRowSuffix**

**sRecentPriceRowPrefix**

<tr>

**sRecentPriceItem**

<td class="recenthtitemprice">_PRICE_</td>