|
Biofilm Eliminator Tablets - Instructions For Use
Usage guide: 1 x 10g tablet for a Whirlpool bath, 1 x 20g tablets for a Spa or Hot Tub
Whirlpool Baths
As a precautionary measure - Do not use this product in enclosed spaces, make sure there is good ventilation.
Dosage: 1 x 10g tablet for up to 1250 Litres of water volume (use more as required)
Place the tablet directly into the bath water & turn on the water massage system, leave running for 10-20 mins.
Immediately after adding the tablet to the Spa/whirlpool you will notice the water will turn yellow as the tablet dissolves. This indicates the tablet is working and is oxidising the contaminants in the system. As soon as this color has completely disappeared, approximately after 1 hour, the water is crystal clear and completely disinfected.
The process usually takes between 1-2 hours
Do not use the whirlpool bath during this time. After approx. one hour, completely drain the spa/whirlpool water, rinse and refill with fresh water.
Your whirlpool/spa is now free of biofilm.
Repeat this treatment as required or at least every 3 months.
Note: Due to the heavy build up of soaps and body oils within a whirlpool bath system we advise that for best results you use this product after a tratement with our Whirlpool system cleaner and degreaser. The whirlpool cleaner degreaser will breakdown the body fats and other contaminants, allowing the power tab to penetrate the biofilm behind. Make sure you drain, rinse and refill before using the power tab
(DO NOT MIX WITH OTHER CHEMICALS)
As far as known Pure-Spa Power Tab can be used, even when (traces of) other chemicals such as Chlorine or Bromine are still in the water. Dissolved in water, the product does not cause danger to the user. Also the smell which appears after the use of these tablets in the spa is not dangerous as far as known.
Hot Tubs
As a precautionary measure - Do not use in enclosed spaces, make sure there is good ventilation.
Dosage: Add 1 x 10g tablet for small spas up to 1250 Litres of water volume (use more as required for larger spas or use one of our 20g Tablets)
We recommend that to start with you remove any visible debris from the cartridge filter (this will increase the efficiency of the product)
Replace the filter cartridge.
Place the tablet directly into the Spa filter basket
Turn on the water massage system & if applicable the filter cycle. Leave running for 10-20 mins or filter cycle duration.
Let the Pure-Spa power tab soak for an hour or two.
Immediately after adding the tablet to the Spa/whirlpool you will notice the water will turn yellow as the tablet dissolves. This indicates the tablet is working and is oxidising the contaminants in the system. As soon as this color has completely disappeared, approximately after 1 hour, the water is crystal clear and completely disinfected.
If it takes a long time for the water to go clear this usually means your spa is relatively clean so its nothing to worry about.
Do not use the spa or bath during this time. After approx. one hour, completely drain the spa water, rinse and refill with fresh water.
If necessary replace your filters too.
Your spa is now free of biofilm. Repeat this treatment at least every 3 months.
Always refer to the label/leaflet with instructions.
DO NOT MIX WITH OTHER CHEMICALS
Frequently asked questions:
What is Chlorine Dioxide?
Chlorine dioxide may sound a lot like chlorine, but it is an altogether different chemical compound with the formula ClO2.
Municipal authorities started using it to disinfect drinking water as early as 60 years ago. It is still widely used for this purpose today. And with good reason: chlorine dioxide is less corrosive than chlorine and superior for the control of legionella bacteria.
It is more effective as a disinfectant than chlorine in most circumstances against water borne pathogenic microbes such as viruses, bacteria and protozoa.
Chlorine dioxide is also used as a disinfectant of medical equipment and for odour control.
When used in spas, it is not only disinfecting the water, but also breaks down the biofilm that may form in the tubing system and which can act as a growing ground for micro-organisms. The particles that result from disintegrating the biofilm is filtered out by the spa filter system.
Is it a problem when traces of other disinfection products are still in the spa water?
No,as far as is known, the Pure-Spa Power Tab can be used even when traces of other disinfection product are in the water.
Is the smell of the water, just after adding the tablet, toxic?
No, the concentration is so little that inhaling does not endanger the health and the smell will disapear soon.
Why has the water turned yellow?
Immediately after adding the tablet to the spa the water will turn yellow because of the dissolving of the tablet. As soon as this color has completely dissapeared, approximately after 1 hour, the water is crystal clear and completely disinfected.
I have read that the water turns transparent again after approximately 1 hour but in my spa it took much longer. How is that possible?
The water in your spa already was very clean. The coloring that occurs will disappear as the product does its job. The product will be used when in action. Since the spa water was very clean already the product has little to do so it takes longer for the color to disappear. Nothing to worry about.
Your advice is to use 10grs per 1,250 liters of spa water. What to do when my spa contains 1,500 liters?
Just use a 20grs tablet or 2 x 10grs. When in doubt, always use a slightly higher dose than recommended. Since chlorine dioxide disappears rapidly after disinfecting, there is absolutely no problem using more than the recommended amount.
A lot of filth appeared in my spa? How can that happen?
It is clear that the Pure-Spa Power Tab did the job. The filth has come out of the tubing of the spa since the product obviously detached the biofilm. The pipes and tubes contained dirt which has come off now, into the spa. The filter will catch these contaminants.
You should completely drain the spa water, rinse and refill with fresh water. If necessary replace your filters too.
Can Pure-Spa Power Tab be used in combination with the ozonator and the UV-lamp of the spa?
Yes, Pure-Spa Power Tab can be used with ozon and UV without any problem. The UV will however reduce the effectiveness of Pure-Spa Power Tab.
How fast is the Pure-Spa power tab at disinfecting water?
Within a couple of minutes all bacteria are killed. Chlorine takes much longer to be effective.
What is the shelf life of Pure-Spa Power Tab?
The products is guaranteed effective for 2 years.
Warning
Chlorine Dioxide Tablets
Ingredients
Sodium Hydrogensulphate, Sodium Chlorite, Disodium Carbonate, Compound with Hydrogen Peroxide
- Keep out of reach of children
- Beware of Off Gassing
- Use only for non-potable water
- Keep out of reach of children & animals
- Store locked up.
- Harmful if swallowed.
- Causes severe skin burns
- May cause damage to organs through prolonged or repeated exposure
- Very toxic to aquatic life.
- Contact with combustible material may cause fire.
- Irritating to eyes and skin.
- Risk of serious damage to eyes. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice.
- Contact with acids liberates very toxic gas
- Wear suitable protective clothing, gloves and eye/face protection. Toxic in contact with skin.
- Keep away from heat. - No smoking.
- Keep away from clothing, incompatible materials and combustible materials.
- Avoid release to the environment.
- Do not breathe dust.
- Dispose of contents and container national and international regulations.
- May intensify fire; oxidiser
- Contact with combustible material may cause fire
- In case of accident or if you feel unwell, seek medical advice immediately (show
the label where possible).
|
|
 Before checking out why not take a look at our clearance lines? - Find some Bargains - save £££ - Click here
|
